If your FLYDIGI Apex 5 gets slippery during long sessions, this pre-cut grip tape from SHADOW BOOLT is the low-cost fix. Below is what it actually is, where it helps, and where you should lower your expectations.
Overview
This is a polyurethane grip tape die-cut specifically for the FLYDIGI Apex 5, with anti-slip texturing and sweat-resistant treatment. Its appeal is simple: you add friction to the shell without replacing or disassembling the controller.
Three colors are offered — Green, Gray, and Black — and they are functionally identical, so the choice is purely cosmetic.
The product has a narrow purpose, which makes the fit clear. If sweat-induced slipping is costing you shots in an FPS or inputs in a fighting game, it helps.
If you just want a premium look, the wear characteristics discussed below may make it a poor value.
Key Features
and When They Matter
The multi-layer texture uses different coarseness on the palm area versus the fingertip area. Palm contact benefits from maximum friction because it is static holding; fingertips involve sliding motion, where excessive grip becomes counterproductive.
That distinction shows up most in games with frequent regripping.
Treat the sweat-absorbing claim as "friction stays usable when damp" rather than "your hands stay dry." Bare plastic fails the moment a thin film of sweat forms, and eliminating that cliff is real value — but in a warm room over several hours, a towel is still the reliable answer.
The repositionable adhesive matters more than it sounds. Grip tape is hard to align on the first try, and a few millimeters of offset leaves an edge that catches your finger.
Being able to peel and redo it saves the install.
Connectivity & Compatibility
The compatibility note is unambiguous: FLYDIGI Apex 5 only, not compatible with other controllers. With a die-cut product this is not a "you can make it work" situation — the cut lines and cutouts follow one specific mold, so applying it to an Apex 4, Apex 3, or an Xbox-style pad leaves lifted edges that peel within days.
| Item | Value |
|---|---|
| Compatible model | FLYDIGI Apex 5 only |
| Material | Polyurethane |
| Colors | Green / Gray / Black |
| Package dimensions | 17.81 × 12.7 × 0.71 cm |
| Weight | 41 g |
The 41 g figure is best read as packaged weight; the tape itself is far lighter, so it will not shift the controller's balance or add fatigue.
Installation is just applying it to the rubberized rear, but preparation decides the outcome. Wipe the surface with alcohol, let it dry fully, then apply.
Rubberized coatings soak up skin oil and will defeat the adhesive even when they look clean. Avoid gripping hard for a few hours after application, and warm the tape in your hands if the room is cold.
Product Info
Material is polyurethane, offered in Green, Gray, and Black. Package dimensions are 17.81 × 12.7 × 0.71 cm at 41 g, and only the grip tape is included — an alcohol wipe may or may not be in the box, so have one ready.
Warranty follows the seller's policy.
Price was ¥2,669 including tax as captured in May 2026. That is a normal-to-slightly-high band for grip tape, which is where die-cut model-specific products generally land.
Prices move often with stock and sales, so check the product page for the current figure. The eBay-side entry is a search listing, so amounts vary per seller.
As of May 2026, ratings stood at 9 reviews averaging 4.9 (98% positive). The score is high, but nine reviews is a very small sample and deserves to be stated plainly.
A 4.9 from thousands of buyers and a 4.9 from nine are not the same signal: early-failure rates and six-month wear simply are not visible yet.
Read it as "no bad reputation has formed," and plan to judge durability yourself.
Alternatives Worth Considering
- Model-specific pre-cut tape (this product) — best fit, no work required, but wasted if you change controllers.
- Generic roll tape you cut yourself — cheaper and universal, but curved surfaces depend on your knife skills and edges lift easily.
- Silicone covers — thicker grip, more about protection than precision; often worse with sweat.
- Gaming gloves or finger sleeves — keep the controller clean and may be the more effective humid-weather fix.
If sweat is the root cause, tape plus finger sleeves usually beats tape alone. Tape raises dry-hand friction; it does not stop perspiration.
Things to Check Before Buying
1. Treat it as a consumable. Polyurethane texture flattens over months of use, especially where the base of your thumb rests, and friction falls with it.
Budget for periodic replacement rather than expecting a permanent upgrade.
2. Adhesive residue and coating damage. Peelable adhesive can still soften and leave residue after long exposure to heat and humidity.
The bigger risk is a controller whose rubber coating has begun to hydrolyze with age — removing tape from that surface can pull the coating off with it. On a used or heavily worn Apex 5, test an inconspicuous area first.
3. Small hands and light grippers benefit less. Grip tape works by converting grip force into friction, so a fingertip-only hold gains little.
Coarse texture can also make fingertips sore over long sessions; more grip is not automatically better.
4. Buying for looks tends to disappoint. Saturated colors like green show oil marks and uneven wear sooner.
If you want the customization to keep looking clean, Black hides wear best.
5. Don't trust the listing metadata blindly. Accessory listings sometimes carry manufacturer, model number, or compatibility fields that don't match the actual item.
Confirm visually from the product images and title that it is the FLYDIGI Apex 5 version — with a die-cut part, the wrong model is simply unusable.
FAQ
Q. Will it fit an Apex 4 or Apex 2? A.
Not recommended. It is cut for the Apex 5, so cutouts and contour lines won't align on other generations, leading to lifted edges.
Q. How many times can I reposition it? A.
No official figure is published. Adhesion weakens with each removal, so plan to finalize placement within one or two tries.
Q. What about warranty?
A. Per the seller's policy. As a consumable accessory, wear-related performance loss is normally out of scope.
Q. Is this enough for heavy sweating?
A. It helps but isn't a cure. Combine with finger sleeves or gloves and regular wiping.
Q. Does it change button or trigger feel? A.
It covers the rear and side hold areas, so button travel is unchanged; the side thickness slightly alters how the shell meets your palm.
Q. Which color should I pick?
A. All three perform identically. Black hides wear; Green is the styling choice.
Best Use Cases
- Owners staying on the Apex 5 long-term — a model-specific cut only pays off if you keep the controller.
- Competitive players losing inputs to sweat — fewer regrips and less aim drift justify the spend.
- Anyone whose sessions run past two hours — friction matters most as grip strength fades.
- Players who want a reversible cosmetic change — unlike paint or disassembly, it peels off.
It is a low priority if you play a few casual hours a week without slipping, don't mind cutting generic tape yourself, or plan to replace the controller soon.
